HBT+ Gravity 6 Mid-Tower Chassis
The HBT+ Gravity 6 is faced with a 3mm thick sheet of aluminum mounted atop a plastic bezel. The corners are rounded, the front is angled, where it is highest on the center line and is cut out for the lower section of the front I/O panel. We also see a slightly raised top section, which inverts the angle used, reminding us of something like the Raven Series of cases.
The front I/O panel is both on top of and down the face of the Gravity 6. Connectivity is all up top, where we find the HD Audio jacks and USB 3.0 ports. The power LED is on the corner where the panels meet, and down the face, is a large power button.
The top panel on the Gravity 6 is angled at the front edge to match the profile of the bezel, but the entire expanse is covered with another 3mm thick sheet of brushed aluminum. The angle we saw at the front is carried down its length, it is cut to surround the I/O panel, and uses the sides and back to allow ventilation.
The left side panel is also made of aluminum, and taking up the majority of the panel is a dark tinted window. The panel is cut along the top and the front edges to clear the venting offered in those locations, and offers rounded corners except at the top, near the back.
Even at the back of the chassis, the angled top continues and has venting on either side of it. Below that, we find the exhaust fan location and the rear I/O cutout. Then, there are seven expansion slots which are vented, the area next to it is as well, but we also find a pair of grommets for external water cooling. At the bottom is where the PSU will reside, and both panels are held in place with thumbscrews.
The right side of the case mimics what we saw on the left, but there is not a large window this time. Just a vast expanse of brushed aluminum to look at, which is cut at the front and top again to allow the same breathability on this side of the Gravity 6.
Underneath of the chassis, we see long plastic feet very near the edges, and they have rubber applied to each of them as well. The back is slotted where the PSU is to go in, and the optional fan location is also well ventilated. We do see tabs for a dust filter, but sadly one is no present here. Near the front of the case is a multitude of holes in the floor, and these are used for pump or reservoir mounting.
PRICING: You can find the Honbontec Gravity 6 Mid-Tower Chassis for sale below. The prices listed are valid at the time of writing, but can change at any time. Click the link below to see real-time pricing for the best deal:
United States: The Honbontec Gravity 6 Mid-Tower Chassis retails for $110 at Amazon.
United Kingdom: Find other tech and computer products like this over at Amazon UK's website.
Canada: Find other tech and computer products like this over at Amazon Canada's website.
Recommended for You
- We at TweakTown openly invite the companies who provide us with review samples / who are mentioned or discussed to express their opinion of our content. If any company representative wishes to respond, we will publish the response here.
Latest News Posts
- NeoGAF goes down, owner embroiled in sexual harrassment
- ASUS ROG Strix GTX 1070 Ti teased with triple-fan cooler
- Bitcoin hits $6000, with $100 billion in value
- Galaxy S9: 6GB RAM, headphone jack is a selling point
- Mass Effect dev: EA only cares about highest returns
- Gigabyte AB-350 G3 CPU LED & No POST after update ->rollback?
- AMD Threadripper vs. Intel Core i9 CPUs Clock for Clock
- ex58-UD3R rev 1.6
- RAID on a new X370 Fatal1ty Gaming X with m.2 SSDs using a PCIe card.
- LGA-775 GA-EP35-DS3P (rev 2.1), Q9550 e0 overclocking advice please?
- Introducing the CYBERPOWERPC Crystal Gaming Series Powered By CORSAIR
- COLORFUL Officially Releases iGame Z370 Vulcan X Motherboard in South Korea
- G.SKILL Releases DDR4-3800MHz 32GB (4x8GB) SO-DIMM Memory Kit for Mini-ITX Motherboards
- EK Water Blocks releases new Slim Series kits
- BIOSTAR releases new RACING Z370GT7 motherboard