Inside The LanCool Dragon Lord PC-K62 Advanced Mid tower Case
Since all the rear panel goodies should be fresh in your mind from the outside image, here's a look from the inside. Most notable is the same VGA locking system I had in my PC-B70, which I really like both its looks and functionality. Just above this mechanism you can see the padlock loop hanging off the back of the chassis for those who need to lock up their hardware. The last thing I want to cover here is the padded rails at the bottom that keep your PSU off the floor of the chassis. In case you put the chassis on the carpet, air can still be drawn into the PSU from inside the PC-K62.
The motherboard tray is set up from the factory ready to accept a full ATX motherboard. The stand offs are already there. Looking around the tray, you will find four wire management holes; two at the bottom, and two on the right side. Something found in a lot of the newer chassis' is the CPU cooler back plate access hole. A nice tray in my opinion for a budget builder's case!
Another look at the floor of the chassis shows a few things. One, there is a plastic rail placed to aide in containing all the PSU wires as they leave the PSU on their destinations to the appropriate component. The right side, or front of the chassis, allows for four 3.5" hard drives to be mounted in a screw-less fashion and slide into the rack. Lastly, we get a glimpse of the front intake 140mm fan.
Stepping back a bit allows the 5.25" drive bays to be seen. The top two have a more simplified screw-less mechanism than did my PC-B70, but the two included devices work just as well as the ones I had seen before and are just as simple to use. Just remove the front bezel and the correct front clip in vented panel, squeeze the screw-less mounts clip to unlock it, swing it left, slide in the drive and snap the lock back into place. The bottom three bays need the use of screws to mount drives in those.
Removing the rear panel gives a good look at the inside of the rear of the motherboard tray and just how you need to route the wires to get them where they need to go. From the outer edge of the support under the tray to the panel is just under ½" of room to route wiring.
Prepping for the installation, I removed the vented plastic front bezel. This allowed me to also gain access to the intakes fan filter that snaps in and out for easy cleaning. As far as removing the vented front sections, there is a tab on either side to release and they slide right out to allow optical drives to show through.
PRICING: You can find products similar to this one for sale below.
United States: Find other tech and computer products like this over at Amazon's website.
United Kingdom: Find other tech and computer products like this over at Amazon UK's website.
Canada: Find other tech and computer products like this over at Amazon Canada's website.
Recommended for You
- We at TweakTown openly invite the companies who provide us with review samples / who are mentioned or discussed to express their opinion of our content. If any company representative wishes to respond, we will publish the response here.
Latest News Posts
- Project Scorpio 4K vs 1080p side by side comparison
- PSN and Xbox LIVE hacker imprisoned for two years
- GALAX GTX 1080 Ti HOF, 3 x 8-pin PCIe power & LCD panel
- NVIDIA's recent Gamer Connect event in India: success
- More 'Star Trek' movies not guaranteed, warns star
- Synology RT2600ac Wireless Router Review
- Cursor disappearing randomly
- AORUS GeForce GTX 1080 Ti 11G Review
- Intel Optane Memory 32GB M.2 NVMe SSD Review
- ASRock Fatal1ty Z270 K6 USB 3.1/TB Issues
- Nokia partners with Lucasfilm to deliver an immersive behind-the-scenes VR experience of Star Wars: The Last Jedi
- New LaCie 2big Dock Thunderbolt 3 bridges the port gap and delivers massive capacity to streamline creative workflows
- ENERMAX launches D.F. STORM, the 3500RPM fan featuring self-cleaning design
- Tenda unveils new USB 3.0 AC1300 wireless network adapter
- SteelSeries brings gamers the world's first dual-surface RGB illuminated mousepad - introducing the QcK Prism